There are quite a number of things to set up in the Woods 50015 timer. If you have just purchased the Woods Timers and you want to carry out an extensive setup on it, then follow the Woods Timers Instructions. You can follow the setup guide here. These step by step instructions will allow you to complete the setup easily and quickly.
Prerequisites Before the Setup of Woods Timers Instructions
What are the things that you should get ready before you begin the setup? Just like most electronic devices that require setup, you have to prepare your Woods timer for all the setup by following the Woods Timers Instructions.
- Charging the battery
The first thing to do is to charge the Woods timer and to do that, you have to plug it into an electric outlet for 10 minutes. Once it has charged adequately, proceed to unplug it from the outlet and hold it to complete the remaining setup steps by using Woods Timers Instructions.
- Reset the memory
This step is very important for Woods timers that have been previously setup. In order to make a new setting on the Woods timer, you have to ensure that the memory is free from any settings at all. To wipe off any previous settings, find a tiny firm object to press the “R” button on the timer. Once you complete that, you now have a new Woods 50015 timer to work with.
- Set the current time
Setting the current time is not difficult. Start by pressing and holding the “Clock” button in place. Now, while you are still pressing down the “Clock” button, press the “Minute” and “Hour” as much as possible. This will display the correct time. Then, you can perform a similar action to set the day. Press down the “Day” button.
Wion Setup Instructions to Program the Timer
- Setup the timer
- To display the “ON/OFF” button you have to press the “Prog” button once. Select “On”.
- Next, to set the time you want, you have to press the “Minute” and “Hour” buttons as much as you want until you get your desired result. If you want to change between AM and PM, you need to toggle the button 123 times.
- Furthermore, to set the day, you have to press the “Day” button as long as you get the correct day.
- To turn off the display program, press the “Prog” button. Select “Off”
- Lastly, if you like to carry out some other settings on the timer program, you can repeat the same steps from the beginning to the end.
- Reviewing ON/OFF settings
It does not matter if you only end up using a few of all the 20 settings that are programmed on your timer, you have to review them. Press down the “Prog” button and scroll through all the 20 ON/OFF settings. While scrolling through, if there is any setting you want to remove or modify, stop there and make your changes.
- Revising a setting
If you have made a setting and you would like to revise it for some reasons, you can definitely go back to it. All you have to do is press down the “Prog” button until the setting you want to modify is displayed. Go ahead and adjust the “Hour”, “Minute”, and “Day” using the ON/OFF settings.
- Connecting or operating the timer
Begin by plugging your device into the timer and turn on the device. Then plug the timer into an electric outlet.
Other Woods Timers Instructions
Removing or restoring a setting
Press down the “Prog” button on your timer device. Keep an eye on the display, once the setting you want to remove or restore pops up, press either the RST or RCL button. You will see the setting on your display replaced with “Dashes” if you are removing a setting. And if you you will see the previous setting if you are restoring a setting, then Woods Timers Instructions will assist you.
How to override the timer
You have to press the “ON” and “OFF” button to display these three options.
ON: The device that is plugged in is permanently powered on
OFF: The device that is plugged in is permanently turned off
AUTO: The device that is plugged in will follow your programmed timer settings
Random setting security features
You need the timer to be on “Auto” mode. When it’s in the mode, you will see “Auto” at the bottom of the display. Then, you have to press the “Clock” button. Next, press and hold down the “HOUR-RND button for 5 seconds. You will see “RND” right next to the minute on the display. Now, the plugged in device will be turned on and off randomly by the random settings function. This will cause the plugged in device to be automatically turned on for 10 to 26 minutes. And it will be turned off for 26 to 42 minutes randomly. Note that this random setting will always outrun any on or off program that you have preset. Nevertheless, if you would like to cancel the random setting that you have set, all you have to do is to press down the “HOUR-RND” button for 5 seconds. Once the “RND” disappears from the display, it means it has been disabled.
The countdown settings
Press down the “Prog” button and scroll through all the 20 settings till you get to the countdown settings “ON/OFF”. Then press the “Hour” and “Minute” buttons to set the countdown. Next, you have to press the clock button and then you have to press and hold in place the RCL-CD button for 5 seconds. This will initiate the countdown feature. Furthermore, on the lower part of the display, “CD” will flash. Once the countdown time is complete, the plugged in device will switch off. In addition, if you want to turn off the countdown feature, put it in the clock mode and press down the RCL-CD button for 5 seconds.
Daylight savings time:
To set this feature, you have to press and hold the “CLOCK-DST” for about 5 seconds. This will push forward your day time up to 1 hour for “Daylight savings time”. And if you would like to disable this function, press down the CLOCK-DST button so that the time will be reversed and set to 1 hour back. And then the “Daylight Savings Time” will be gone. These Woods Timers Instructions will help you to complete the procedure effortlessly.
Read More: WiOn 50055, Wion 50053, Wion 50050, Wion 50054